VRF (Variable Refrigerant Flow) Multi-Split Air Conditioner Terminology and Key Concepts
VRF stands for Variable Refrigerant Flow ; Daikin's brand name is VRV (Variable Refrigerant Volume) . Both operate on the same technical principle and are often used interchangeably in the industry. Essentially, it's a direct-evaporation DX multi-split refrigerant system where the refrigerant is directly delivered to the indoor unit, without relying on chilled water for air distribution.
I. Core Abbreviations and Terms
1. ODU : Outdoor Unit
2. IDU : Indoor Unit
3. EEV : Electronic Expansion Valve ( each indoor unit is independently configured to precisely regulate refrigerant flow, which is the core of zoned temperature control).
4. Refnet Joint / Branching Pipe : Y-type branching joint for refrigerant copper pipes, used for distributing refrigerant, VRF specific, cannot be replaced by ordinary tees.
5. BS Box (Branch Selector) : A branch selector , only found in heat recovery VRF systems, used to switch the cooling/heating of a branch to achieve simultaneous cooling and heating.
6.DX : Direct Expansion, Direct Evaporation
7. Inverter : mainly DC inverter compressors; there is also a digital scroll compressor ( non-inverter, variable capacity unloading by piston).
8. BMS/BA : Building Automation System. VRF can be accessed via a gateway using Modbus or BACnet for centralized control.
9. COP / IPLV(C) : Performance factor, comprehensive part load energy efficiency (VRF has an advantage in part load, IPLV is more valuable than rated COP).
10. GWP : Global Warming Potential, environmental performance index of refrigerants (R32 < R410A)
11. Diversity Factor : Load simultaneity rate
12. Connection Ratio : The sum of the rated capacity of all indoor units ÷ the capacity of the outdoor unit, typically 50% to 130%, with over-sizing allowed by the simultaneous use factor.
II. System Classification (Key Point)
1. Heat pump type VRF (ordinary cooling and heating type, two-pipe) : one set of gas pipes + liquid pipes, the entire system can only cool or heat at the same time; it cannot cool and heat at the same time, and has a high cost performance.
2. Heat recovery type VRF (three-pipe) : gas pipe, liquid pipe, low-pressure balance pipe + BS branch box; some rooms are cooled while others are heated . Waste heat from the cooled rooms is directly recovered to the heated rooms, resulting in higher energy efficiency. It is commonly used in hotels and office buildings, but the cost is higher.
III. Core Component Terminology
Variable frequency scroll compressor : VRF heart, continuous speed regulation (10%~100%), not start-stop control, matching dynamic load; mainstream commercial scroll compressor, small model rotary type.
Four-way reversing valve : Used for reversing the heat pump system and switching between cooling and heating cycles.
Oil separator : Separates the refrigerant oil in the compressor exhaust and returns it to the compressor. Oil return is the biggest challenge in VRF operation and maintenance , as long pipelines and low loads are prone to oil blockage.
Liquid receiver/gas-liquid separator : buffer and prevent liquid hammer.
Filter + Dryer : Filters impurities, absorbs moisture in the refrigerant, and prevents ice blockage.
Temperature thermistor (temperature sensor) : Collects the temperature of the coil, intake and exhaust, and ambient temperature, providing signals to the EEV and inverter board.
Condensate lift pump : Standard configuration for ducted indoor units and cassette indoor units, it lifts the condensate to meet the drainage slope of the ceiling.
IV. Refrigerant and Piping Terminology
Refrigerant : Mainstream R410A and R32; R32 is flammable and has higher installation and maintenance requirements.
Phosphorus-deoxidized seamless copper pipe : VRF refrigerant pipe, must be nitrogen-filled and welded to prevent oxide scale inside the pipe; post-weld pressure holding and leak detection, and deep vacuuming are mandatory procedures.
Equivalent pipe length : including branch pipes and the length after considering the local resistance of bends. The manufacturer has maximum total length, length after the first branch, and height difference limit (the limit is different for outdoor unit higher than indoor unit/indoor unit higher than outdoor unit).
Pressure holding : High-pressure nitrogen pressure holding (generally 4.0MPa, more than 24 hours), leak testing; refrigerant pressure holding and leak testing are strictly prohibited.
Vacuuming : Refrigerant should only be added after the system vacuum level reaches the standard; direct evacuation is not allowed.
Adding refrigerant : The refrigerant on the VRF outdoor unit nameplate is the basic amount. When the copper pipe is extra long, add refrigerant according to the liquid pipe diameter + length.
V. Control Logic Knowledge Points
1. Outdoor unit: Variable frequency compressor regulates total refrigerant output.
2. Each indoor unit: Independent EEV opening, with separate control over the amount of refrigerant entering the unit.
3. Communication bus: Dedicated communication line between indoor and outdoor units (F1/F2, P1/P2, A/B, etc., different brands have different terminals) for exchanging fault information, temperature information, and mode information.
4. Control hierarchy: Standalone wired controller → Area centralized control → Central controller → Building Management System (BMS).
5. Anti-cold air, defrosting, oil return operation, and oil balance are all preset protection programs for the outdoor unit.
VI. Key Knowledge Points in Design
1. Connectivity : 100% is not necessary. Offices and hotels often achieve 110% to 130% because rooms will not be fully loaded at the same time. However, areas such as server rooms and kitchens that are constantly under full load should not be over-provisioned.
2. Piping height difference limit : The height difference between the outdoor unit and the farthest indoor unit, and the height difference between adjacent indoor units. Exceeding the limit will result in poor oil return and uneven refrigerant distribution.
3. Selection of manifolds : They should be matched according to the capacity of the front and rear pipes, and should not be mixed or mismatched with different diameters.
4. Fresh air : VRF itself does not have a fresh air supply. Fresh air needs to be supplied separately with HRV total heat exchanger and fresh air unit. It cannot be directly supplied with air exchange by the indoor unit.
5. Low-temperature heating : Heating capacity decreases in low-temperature environments, so a low-temperature high-heat VRF with jet enthalpy enhancement (EVI) is required.
VII. Frequently Used Terminology for Faults & Maintenance
Liquid slugging : Liquid refrigerant returns to the compressor, damaging the scroll plate and causing a fatal malfunction.
Oil blockage : Refrigerant oil remains in the pipeline, causing compressor wear due to insufficient oil supply. This is more common under low load and in long pipelines.
Refrigerant imbalance : The refrigerant is not distributed evenly among the indoor units, some are cold and some are not.
U4/L4 and other fault codes : communication failures and outdoor unit abnormal codes of brands such as Daikin and Hitachi (brand proprietary).
Thermal drift : Temperature sensor drift causes EEV adjustment to become inaccurate.
Oil return operation : The outdoor unit is forced to run at high frequency at regular intervals to bring the oil in the pipeline back to the compressor.